AirSense 9-30521 MiniLaser Input/Output Functional Module | 2 Programmable Inputs, 5 Relay Outputs
£102.19 (inc VAT: £122.63)
Key features
- Dip-switch configuration without a PC
- Fits expansion sub-module slot 1 or 2
- Onboard LED shows power and communication status
Downloads
Summary
The AirSense 9-30521 MiniLaser Input/Output Functional Module gives you two extra programmable inputs and five latched relay outputs for your MiniLaser aspirating smoke detector (ASD) installation, without the cost or wiring complexity of separate interface hardware.
View full overview Show less
For sites that need more than a basic fire/fault interface, such as reporting all four alarm levels to a fire alarm control panel or building management system (BMS), this module lets you win that scope without swapping out the base detector. It also opens up remote control functions like day/night mode changeover, remote reset and ClassiFire Override, which are useful where a client needs sensitivity dialled down during predictable smoke events such as stage effects or controlled open fires.
You install it directly into the MiniLaser expansion sub-module, in either slot 1 or slot 2, so it fits into whatever layout you have already planned. Configuration is done through the Remote software via the MiniLaser’s USB-C interface for full control, or via dip-switch for a fast, PC-free commission with sensible default behaviours.
Features
- Two programmable inputs – wire in remote day/night changeover, remote reset, ClassiFire Override or power-supply fault monitoring from a single module
- Five latched relay outputs – report all four ASD alarm levels plus a dedicated fault output to the fire panel or BMS
- Normally open or normally closed contacts – match the output configuration to whatever third-party equipment you are interfacing with
- Slot 1 or slot 2 installation – fits the MiniLaser expansion sub-module in either position for flexible system layouts
- Onboard status LED – quickly check power, communication status and communication faults on site
- Two configuration routes – use Remote software for full access to advanced settings, or dip-switches for a quick PC-free commission with preloaded defaults
FAQ
Yes. The 9-30521 is designed to install in either slot 1 or slot 2 of the MiniLaser expansion sub-module, so you can plan your enclosure layout around the job rather than around the module. Not necessarily. The dip-switch mode gives you preloaded default behaviours for the inputs and outputs so you can get a system running without a PC, though full configuration via Remote software is available if the job needs more granular settings. This single module combines 2 programmable inputs with 5 programmable relay outputs, so in many cases one 9-30521 can cover both monitoring and control functions on a job rather than needing separate input-only and output-only modules. Each of the two supervised inputs requires a 15 KΩ 5% 1/4 W end-of-line resistor to enable fault detection on the wiring. The exact fitting position and wiring diagram are given in the installation manual, so check that document before terminating the circuit. No separate supply is specified; the module fits directly into the MiniLaser expansion sub-module slot and is powered from the host detector. If you are populating multiple expansion modules on one MiniLaser, confirm the combined current loading with AirSense technical support before finalising the design. The 9-30521 carries CPR and EN 54-20 certification, which is the relevant standard for aspirating smoke detection equipment, so it is appropriate for use within EN 54 compliant installations alongside the MiniLaser detector. For enclosure and mounting requirements under BS 5839-1, refer to the installation manual.Can this module go in either slot of the expansion sub-module?
Do I need a laptop on site to commission it?
Can one module handle both input and output duties, or do I need separate units?
How do I set up the end-of-line resistor on a monitored input?
Does the module need its own 24V power supply?
Is this module suitable for EN 54 compliant fire systems?
Specifications
| Input Quantity | 2 |
|---|---|
| Input Type And Rating | Supervised |
| Input Termination | 15 KΩ 5% 1/4 W |
| Input Programmable | Yes |
| Output Quantity | 5 |
| Output Type And Rating | Voltage free (contact rating 2 A at 30 VDC / NO/NC/C) |
| Output Programmable | Yes |
| Physical Dimensions | 92 x 67 x 19 mm (W x H x D) |
| Operating Temperature | -10 to +60°C |
| Relative Humidity | 0 to 90% noncondensing |
| Environment | Indoor |
| Certification | CPR, EN54-20 |
Downloads
- Datasheet (Adobe PDF)