
Updated 9 November 2026: reviewed against Eaton’s archived JSB panel information and current detector and BiWire Flexi documentation.
Looking for replacement parts for a JSB Firedex BiWire fire alarm? Start with the complete panel model and the detector/base combination. Eaton confirms that the original JSB BiWire control-panel range is discontinued. A current Eaton detector or a product described as “BiWire” should not be ordered as an automatic replacement simply because the brand or appearance matches.
This guide helps you identify the legacy panel, collect the details needed for a compatibility check, and understand the difference between replacing a device and planning a system upgrade. It is a parts-selection guide for discussion with your fire alarm maintainer; it does not replace the installation instructions or a site assessment.
Identify the panel · Before-ordering checklist · Parts and compatibility table · Upgrade options · FAQs
Which JSB Firedex BiWire panel do I have?
Eaton’s archived JSB BiWire specifications list the following models. The original technology allowed BiWire detectors, sounders, LED beacons and relay modules to share the same zone wiring.
| Full model code | Legacy panel | What to record |
|---|---|---|
| FX2202BW | 2-zone JSB BiWire panel | Full label, panel condition and connected devices. |
| FX2204BWHMO | 4-zone JSB BiWire panel | Full suffix and any programmed site functions. |
| FX2208BWHMO | 8-zone JSB BiWire panel | Full suffix, zone use and any repeater connections. |
You may see searches or paperwork shortened to “Firedex 2202”, “2204” or “2208”. Those numbers alone are not a sufficient compatibility check. Use the full label, the correct manual and the installed device references; do not infer the system from the enclosure alone. Ask your maintainer to obtain any information that requires opening equipment.
Before ordering: a JSB BiWire replacement checklist
- Photograph the panel label. Record the complete model, including BW/BWHMO suffixes, and any revision information.
- Record the detector reference and its base separately. A detector head and a sounder base are separate parts; their physical fit is only one check.
- Identify the job. Is it a failed detector, a damaged call point, additional devices, a panel fault or a larger extension?
- Record the existing devices on the affected zone. Include sounders, beacons, relays and the end-of-line arrangement.
- Ask the maintainer to check capacity and operation. Adding a device needs more than a matching terminal layout: the zone load, alarm operation and fault monitoring must also be suitable.
- Obtain confirmation for the complete combination. Give Eaton or your maintainer the panel, detector and base codes, rather than asking whether an item works with “JSB”.
- Plan testing and records. Agree the work, any temporary arrangements, and the testing and logbook entries needed after the change.
Replacement parts: what is confirmed, and what needs checking?
The table separates manufacturer-identified products from a promise that they can be fitted to every legacy installation. Eaton’s current product-range information is useful evidence, but a listing in the newer range does not by itself confirm backward compatibility with an FX2200BW panel.
| Part or system | Manufacturer information checked | Decision before ordering |
|---|---|---|
| Original JSB FX2200BW panel range | Eaton marks the JSB BiWire control panels as discontinued and no longer available. | Identify the exact panel and fault before choosing repair or replacement. |
| FXN922 conventional detector | Eaton identifies this as a conventional 5-in-1 detector. Its technical data names the EFXN520 (FXN520) mounting base. | Confirm the legacy panel and any sounder-base combination separately; this base specification is not a universal JSB-system approval. |
| EFBW5IN1DET BiWire detector | Eaton places its BiWire 5-in-1 detector in the current BiWire Flexi system range. | Do not substitute it for FXN922 on an old panel without exact compatibility confirmation. |
| EF5021BWS / EF5021BWSB sounder / sounder-VAD bases | These are listed in Eaton’s current BiWire Flexi compatibility guide. | Check the exact detector, base and legacy-panel combination. A current-range listing does not establish compatibility with every old base. |
| Manual call points and wall sounders | Eaton has distinct conventional and BiWire device ranges. | Match the full part number, zone technology and system requirements. Do not treat all Eaton call points or sounders as interchangeable. |
| BiWire Flexi panel | Each zone can be configured for either conventional or two-wire devices. | Plan the upgrade against the supported device list; do not assume all original JSB devices or end-of-line units can be retained. |
Sources: Eaton conventional detector range, Eaton BiWire detector range and Eaton BiWire Flexi panel information. For a legacy combination that is not explicitly covered, Eaton lists technical support on its archived JSB product page.
I need to add or replace an existing device
Detectors and mounting bases
The FXN922 detector combines optical smoke, optical/heat and three heat modes in one selectable conventional detector. Eaton’s technical data specifies EFXN520 (FXN520) as its compatible mounting base. Huvo lists that base under Eaton conventional detector base.
If the existing detector sits on a sounder base, record that base’s full reference as well. Do not assume that a detector that fits a standard base is approved for every older sounder base. Have the complete assembly checked before ordering, including head-removal fault indication and the required detection mode.
Manual call points
Record the existing call-point code and whether it belongs to the legacy two-wire system or a conventional circuit. A current call point with a similar case is not enough evidence of electrical compatibility. Ask for the exact replacement reference for your panel and zone.
Sounders, beacons and relay modules
Include the complete model of each signalling device or interface in the compatibility check. The legacy JSB system used shared zone wiring, so do not assume a conventional sounder or a newer BiWire accessory is a drop-in replacement. The maintainer should check loading, alarm behaviour and any connected equipment as part of the change.
My panel is faulty or I require a larger size
A failed control panel needs a system-level review. Eaton’s archived page confirms the original JSB BiWire range is unavailable; it does not establish that a newer panel can operate every original field device. Ask for an inventory of what can be retained, what must be replaced and what still needs confirmation before approving the upgrade.
The current Eaton BiWire Flexi panel is available in 2-, 4- and 8-zone versions. Eaton says each zone can be configured for conventional or two-wire devices. That flexibility makes it an option to assess with the designer, rather than a guarantee that the old JSB zone equipment can remain unchanged.
Current products for a planned BiWire Flexi upgrade
The products below are for an upgrade designed around the current Eaton range. They are not presented as automatic replacements for an original JSB panel or detector. Confirm the device schedule, bases, zone configuration and required accessories before ordering.
Eaton’s current BiWire 5-in-1 detector is EFBW5IN1DET. Keep this reference separate from the conventional FXN922 when discussing replacements. Check the mounting base and any sounder/VAD requirements as part of the new system specification.
Browse the Eaton BiWire Flexi range, or contact Huvo with your full panel and device references so the required parts can be identified.
JSB Firedex BiWire FAQs
Is the JSB Firedex BiWire system discontinued?
Yes. Eaton’s archived JSB BiWire control-panel page marks the range as discontinued and no longer available. That is separate from deciding whether a particular installed system can continue in use or needs replacement.
Does “Firedex 2204” identify the right replacement parts?
Not on its own. Record the complete model and suffix. Eaton lists FX2204BWHMO as its 4-zone legacy JSB BiWire model; shortened names can omit the information needed to distinguish the system.
Are FXN922 and EFBW5IN1DET the same detector?
No. Eaton identifies FXN922 in its conventional detector range and EFBW5IN1DET in its current BiWire range. Their similar five-mode descriptions do not establish interchangeability on a legacy panel.
Can I reuse the old detector bases?
Check the exact base and the proposed detector together. Eaton’s FXN922 data specifies EFXN520 (FXN520), but that does not establish approval for every older sounder base or prove that every installed base can be retained during a panel upgrade.
Can a BiWire Flexi panel replace my JSB panel without changing the devices?
Do not assume so. Flexi supports conventional or two-wire configuration on each zone, but the installed detectors, sounders, call points, interfaces and end-of-line arrangement must be checked against the proposed system.
Does discontinued mean my installed system is automatically non-compliant?
A product’s sales status alone does not settle the suitability of an installed fire alarm. Have your competent fire alarm maintainer assess its condition, coverage, operation, documentation and supportability for the premises. Normal operation alone is not evidence that every requirement has been met.
Manufacturer references and the correct manual
Use the full model when choosing documentation. Eaton’s archived JSB resources include the FX2200BW datasheet and a 4-/8-zone instruction manual and logbook. The latter is labelled FX2204/2208 BiWire: do not treat it as the manual for every Firedex panel or the 2-zone version. Older manuals describe their original equipment and should not be taken as approval for a later replacement product.



