XFP CAST Programming Tool
- Intuitive and easy-to-use programming tools
- Includes USB memory stick and programming lead
- Free software updates available
C-Tec
Filters
System Type Addressable
Colour White
10-20 Zone Master Controller Available In Flush or Surface Enclosure
- Master controller with 10 or 20 zones.
- Compatible with C-TEC’s entire range of 800 Series field devices.
- Housed in an attractive flush or surface mounetd plastic enclosure.
- Two call levels - standard (constant tone) and emergency (intermittent tone).
- Optional mute and call accept/reset buttons.
C-Tec ActiV Conventional Base Sounder VAD (C-3-8.5)
- Third-party certified to EN54-3 (Sounders) and EN54-23 (VADs)
- Provides 'C-3-8.5' light distribution (min 0.4 lux over a 3 x 8.5m cylindrical area)
- Impressive 96dB(A) sound output @ 1m
- Includes 31 selectable primary tones and an optional secondary tone
- Two volume levels (high and low)
- Three selectable VAD flash rates (0.5Hz, 1Hz, OFF)
- Alarm Current at 30Vdc = 12.2mA (0.5Hz) or 19.5mA (1Hz)
- Alarm Current at 18Vdc = 14.5mA (0.5Hz) or 25mA (1Hz)
- Optional BF330CTLIDW white or BF330CTLIDR red cap available for stand-alone use
- Supplied with a BF431QCP quick connect plate and detector spur wires
- IP21C rated
Device Type Sounder, VAD
System Type Conventional
Environment Indoor
Complete the setup
Hand-picked accessories for this item
C-Tec BF366 24V 5A Isolatable Relay On A Plate
- Isolating keyswitch to temporarily disable outputs when testing fire alarm system.
- LED flashes and buzzer soudners when active.
- Fits onto a standard single gang back box.
C-Tec BF367 Auxiliary Device Isolator
- Isolate a 24V output for fire alarm panel.
- Prevent auxillary equipment such as autodiallers from activating.
- Label includes area to write on description.
C-Tec BF431A/CX/W Addressable XP95 Compatible 96dB Base Sounder
- Impressive 96dB(A) sound output @ 1m.
- Supplied with a BF431QCP quick connect plate and detector spur wires.
- Onboard short-circuit loop isolator.
Device Type Sounder
Protocol XP95
System Type Addressable
C-TEC BS 5839-6 Hush Button
- Fully Compliant with BS 5839 Part 6
- Works with Apollo XP95/Discovery and Hochiki ESP Protocols
- Fitted by a standard 25mm Back Box
- Built in Loop Isolator
Protocol Hochiki ESP, Apollo
CAST Detector Base
- The CA408 is third-party LPCB certified to the relevant parts of EN54 standards
- It offers a simple "click and twist" design for easy installation and can be ceiling-mounted in any orientation
- The base is also compatible with C-TEC's CAST protocol sounder VADs and can connect to a remote LED indicator
System Type Addressable
Colour White, Black
C-Tec CFP & XFP Network Communication Card - 32 Zone Panels
32 Zone Network Card for XFP Panel
C-Tec CFP Panel Network Communication Card Kit
- Network Card for CFP Panels
C-TEC CFP Relay Output Card - 12 Relays
- Provides Reset, Fault, Aux Fire and Remote Relays
- 8 Outputs per Zone Relays
C-Tec CFP Relay Output Card - 2 Relays
- 2 Output Relays Zonal Board
C-Tec CFP Relay Output Card - 4 Relays
- 4 Output Relay Zonal Board
C-Tec CFP Relay Output Card - 8 Relays
- 8 Relay Output Zonal Board
C-Tec FF502P 4 Zone Sounder Circuit Extender Kit
- Provides four extra conventional sounder circuits with open and short circuit fault monitoring.
- Compatible with most manufacturers' fire alarm control panels.
- Supplied on a double gang plate.
C-Tec Hi-Output XP95 Wall Sounder
Key Features
- Third-party certified to EN54-3 (Sounders) and 17 (Isolators) by the LPCB
- Impressive 103dB(A) sound output @ 1m
- Onboard short-circuit loop isolator
- 550µA quiescent current./li>
- 5mA alarm current @24V DC (sounder on max)
- Group addressing facility allows multiple devices to be operated simultaneously
- 7 selectable volume levels and up to 15 selectable tone pairs
- IP21C (Type A) rated.
Device Type Sounder
Protocol XP95
System Type Addressable
C-Tec Lid for Base Sounder in White or Red
- Optional lid for C-Tec base sounders.
- Available in white or red.
Colour White, Red
C-Tec NC302RXC Master Infrared Ceiling Receiver
- Receives line-of-sight infrared signals from up to 10 meters away, depending on environmental conditions
- Includes a red LED that confirms when a call has been made
- Requires a separate remote reset point, such as a button or keyswitch, to cancel calls
C-Tec NC802DB Standard Call Point, Button Reset with Remote Socket
- The call point features a button reset mechanism
- It includes a 6.35mm jack plug socket for remote operation
- The design is suitable for use in 800 Series Call Systems
C-Tec NC802DEB-1/2 Emergency Call Point, Button Reset with Remote Socket
- Includes a 6.35mm jack plug socket for connecting optional devices like a tail call lead or pressure mat
- Features a red reassurance LED that confirms when a call has been made
- Provides an onboard reset button to cancel standard and emergency calls made from the NC802DEB-1/2, as well as standard calls from other devices on the same zone
C-Tec NC802DEWA IP67 Emergency Sauna/Steam/Wet Room Alarm Point, Requires NC889ERM
- It has a surface-mounted design with a 35mm black back box, yellow call point, and white push button
- It comes supplied with a set of branding stickers
- The IP67 rating ensures it is protected against water ingress and can withstand the harsh conditions found in saunas and steam rooms
C-Tec NC802DEWP IP67 Emergency Pool Alarm Point, Requires NC889ERM
- IP67 rated panic alarm point for swimming pools
- Compatible with 800 Series Call System via NC889ERM
- Includes a black back box, blue call point, and white push button
C-Tec NC804DE Emergency Only Call Point, Button Reset
- The onboard reset button can cancel emergency calls made from the NC804DE and standard calls made from other devices on the same zone
- It is ideal for use as a reset point for ceiling pull units, allowing a more urgent emergency call to be made if additional assistance is required
- A red reassurance LED confirms when a call has been made