C-Tec

• Intuitive and easy-to-use programming tools
• Includes USB memory stick and programming lead
• Free software updates available

• Master controller with 10 or 20 zones.
• Compatible with C-TEC’s entire range of 800 Series field devices.
• Housed in an attractive flush or surface mounetd plastic enclosure.
• Two call levels - standard (constant tone) and emergency (intermittent tone).
• Optional mute and call accept/reset buttons.

• Third-party certified to EN54-3 (Sounders) and EN54-23 (VADs)
• Provides 'C-3-8.5' light distribution (min 0.4 lux over a 3 x 8.5m cylindrical area)
• Impressive 96dB(A) sound output @ 1m
• Includes 31 selectable primary tones and an optional secondary tone
• Two volume levels (high and low)
• Three selectable VAD flash rates (0.5Hz, 1Hz, OFF)
• Alarm Current at 30Vdc = 12.2mA (0.5Hz) or 19.5mA (1Hz)
• Alarm Current at 18Vdc = 14.5mA (0.5Hz) or 25mA (1Hz)
• Optional BF330CTLIDW white or BF330CTLIDR red cap available for stand-alone use
• Supplied with a BF431QCP quick connect plate and detector spur wires
• IP21C rated

• Isolating keyswitch to temporarily disable outputs when testing fire alarm system.
• LED flashes and buzzer soudners when active.
• Fits onto a standard single gang back box.

• Isolate a 24V output for fire alarm panel.
• Prevent auxillary equipment such as autodiallers from activating.
• Label includes area to write on description.

• Impressive 96dB(A) sound output @ 1m.
• Supplied with a BF431QCP quick connect plate and detector spur wires.
• Onboard short-circuit loop isolator.

• Fully Compliant with BS 5839 Part 6
• Works with Apollo XP95/Discovery and Hochiki ESP Protocols
• Fitted by a standard 25mm Back Box
• Built in Loop Isolator

• The CA408 is third-party LPCB certified to the relevant parts of EN54 standards
• It offers a simple "click and twist" design for easy installation and can be ceiling-mounted in any orientation
• The base is also compatible with C-TEC's CAST protocol sounder VADs and can connect to a remote LED indicator

32 Zone Network Card for XFP Panel

• Network Card for CFP Panels

• Provides Reset, Fault, Aux Fire and Remote Relays
• 8 Outputs per Zone Relays

• 2 Output Relays Zonal Board

• 4 Output Relay Zonal Board

• 8 Relay Output Zonal Board

• Provides four extra conventional sounder circuits with open and short circuit fault monitoring.
• Compatible with most manufacturers' fire alarm control panels.
• Supplied on a double gang plate.

• Third-party certified to EN54-3 (Sounders) and 17 (Isolators) by the LPCB
  • Impressive 103dB(A) sound output @ 1m
• Onboard short-circuit loop isolator
• 550µA quiescent current./li>
• 5mA alarm current @24V DC (sounder on max)
• Group addressing facility allows multiple devices to be operated simultaneously
• 7 selectable volume levels and up to 15 selectable tone pairs
• IP21C (Type A) rated.

• Optional lid for C-Tec base sounders.
• Available in white or red.

• Receives line-of-sight infrared signals from up to 10 meters away, depending on environmental conditions
• Includes a red LED that confirms when a call has been made
• Requires a separate remote reset point, such as a button or keyswitch, to cancel calls

• The call point features a button reset mechanism
• It includes a 6.35mm jack plug socket for remote operation
• The design is suitable for use in 800 Series Call Systems

• Includes a 6.35mm jack plug socket for connecting optional devices like a tail call lead or pressure mat
• Features a red reassurance LED that confirms when a call has been made
• Provides an onboard reset button to cancel standard and emergency calls made from the NC802DEB-1/2, as well as standard calls from other devices on the same zone

• It has a surface-mounted design with a 35mm black back box, yellow call point, and white push button
• It comes supplied with a set of branding stickers
• The IP67 rating ensures it is protected against water ingress and can withstand the harsh conditions found in saunas and steam rooms

• IP67 rated panic alarm point for swimming pools
• Compatible with 800 Series Call System via NC889ERM
• Includes a black back box, blue call point, and white push button

• The onboard reset button can cancel emergency calls made from the NC804DE and standard calls made from other devices on the same zone
• It is ideal for use as a reset point for ceiling pull units, allowing a more urgent emergency call to be made if additional assistance is required
• A red reassurance LED confirms when a call has been made