Mirrored or Brushed Stainless Steel Finishes For Advanced MxPro5 Panels
- Clean and stylish.
- Aesthetically pleasing.
- High class look.
Filters
Morley 797-076 'L' Shaped Mounting Bracket
- Requires a Standard RS485 Card To Be Fitted In The Main Control Panel (Supplied Seperately).
Morley MAx Repeater or Mimic Panel
- Single hardware with dual functionality (programmable as a Repeater or a Mimic)
- Full network visibility and control (Reset, Silence/Resound and Mute Buzzer)
- USB port for firmware upgrades and event history retrieval
- Modern compact design
Morley ZX Hi-485 Communication Module
- Requires a Standard RS485 Card To Be Fitted In The Main Control Panel (Supplied Seperately).
Morley-IAS DX Connexion 40 or 80 Zone LED Kit
- Zonal LED card for DX Connexion panels.
- Available with either 40 or 80 LEDs.
Morley-IAS DX Connexion Network Card
- Network card for DX Connexion panels.
- Required to connect multiple panels together in a network.
Network Card For Advanced MxPro 5
- Network card for Advanced MxPro 5 panels.
- Large Ad-NeT+ 200 Panel Network.
- Up to 1.5Km between Control Panels.
- Standard or Fault-Tolerant versions available.
PENN Peripheral Expanson Network Node For Advanced MxPro 5
- Lets you install peripherals in remote locations without an additional panel.
- Network in-built – either Standard or Fault Tolerant.
- Up to 32 Nodes in Standard configuration and Up to 200 Nodes in FT configuration.
Printer Assembly For Advanced MxPro 5
- Fast instant response.
- Fast and silent operation.
- Thermal printer.
Routing Termination Card For Advanced MxPro 5
- Routing Termination Card For Advanced MxPro 5 panels.
Semi-Flushing Bezel For Advanced MxPro 5 Panels
- Semi flush fitting for all MxPro 5 panels.
- Picture frame effect for ease of installation 30mm flange for control panels, 20mm for repeaters.
SmartConnect Mulit-Loop RS232 Printer Module
- Designed to EN54 requirements
- Use to interface to RS232 devices
- 5V aux output (ofr use with panel printer only)
- Extensive front unit indications
- Quick and easy to install by plugging the RJ45 cable into the module and control panel (cable supplied with Unit)
SmartConnect Multi-Loop 6 Way Conventional Zone Monitor
- Designed to EN54 Part 2
- 6 x Conventional Zones
- Each zone is monitored for open & short circuit
- Extensive front unit status indications (see table below)
- Quick and easy to install by plugging the RJ45 cable into the module and control panel (cable supplied with unit)
- Each zone input can be configured as either Alarm or Technical Alarm
SmartConnect Multi-Loop Alarm Circuit Module
- Can be configured as an alarm output or a power output
- 2 x output circuit (500mA each)
- Extensive front unit status indications
- Quick and easy to install by plugging the RJ45 cable into the module and control panel (cable supplied with unit)
- Power limited
SmartConnect Multi-Loop Card Module
- Designed to EN54 requirements
- Supports up to 250 addresses
- “Heartbeat LED” that shows communication between the module and the motherboard
- Extensive front unit status indications
- Time saving AUTO-LEARN facility
- 450mA max load (at 20 ohms loop resistance)
- Double address detection
SmartConnect Multi-Loop Gas Detection Module
- Each SCM-4-20 module has 2 available circuits
- Each circuit will allow a single connection of a 4-20mA device
- Extensive front unit status indications
- Compatible with any Smart Connect Multiloop Panel
- Quick Connect Din Rail Mount
SmartConnect Multi-Loop Multi-Input Module
- Designed to EN54 Part 2
- Each input is monitored for open & short circuits
- Extensive front unit status indications (See Datasheet)
- Quick and easy to install by plugging the RJ45 cable into the module and control panel (cable supplied with Unit)
- Each input can be configured as either Alarm or Supervisory
SmartConnect Multi-Loop Multi-Relay Output Module
- Designed to EN54 Part 2
- 3 x Form C relay outputs
- Each relay can be programmed to activate on Alarm, Technical Alarm, or Fault.
- Extensive front unit indications (see datasheet)
- Quick and easy to install by plugging the RJ45 cable into the module and control panel (cable supplied with Unit)
SmartConnect Multi-Loop Repeater
- 4.3” colour touch screen display
- 8032 event log entries
- Up to 64 panel peer-to-peer network
- 13 status LED indicators
- 5 function button controls
- Fully functioning repeater provides the ability to program a networked Smart Multi-loop control panel from the front screen
- Accommodates wiring lengths up to 1000 metres from the control panel for added design and install flexibility
- Network can we wired in either a bus or a ring topology if a redundant path is required
- 8 password protected access accounts available (1 admin level, 7 user level)
- Uncluttered and intuitive interface allows alarms, tech alarms, and fault events to be easily viewed
- Low power consumption
- Small enclosure
SmartConnect Multi-Loop RS485 Network Module
- Designed to EN54 requirements
- Peer-to-peer networking
- Comprehensive cross network cause & effects
- Remote programming over the network
- The network can be configured with either a ring or bus topology
- Extensive front unit status indications (See datasheet)
- Quick and easy to install by plugging the RJ45 cable into the module and control panel (Cable supplied with unit)
SmartConnect Multi-Loop TCP/IP Module
- Designed to EN54 requirements
- TCP-IP output via RJ45
- Zeta Remote monitoring via a desktop PC or smartphone via the cloud
- Remote control via the cloud
- Responsive web interface
- “Heartbeat LED” that shows communication between the module and the motherboard
- Extensive front unit indications
- Quick and simple to install
Sounder Active EOL For Advanced MxPro 5
- For use with EN54-13 Compliance.
- Supports device removal.
- For use with all MxPro 5 series control panels.
