Fire Alarm Detectors
Showing 457–480 of 577 results
-
-
Fyreye Relay Base
The Relay base is mainly used on 12V security systems to signal detector operation to the panel. They can also be used on 24V fire systems where the activation of a particular detector requires a signal to nearby equipment (door holders for example).
-
Gent ES Detect Conventional Heat Detector
- Range of detection technologies with advanced microprocessor controlled detection
- Self monitoring for contamination, to maintain optimum sensitivity throughout whole life
- Compatible with diode base to monitor detector removal
-
Gent ES Detect Conventional Standard Base With or Without Diode
- Standard base for ES Detector conventional Gent detectors.
- Available with optional diode.
-
Gent ES Optical Smoke Conventional Detector
- Optical smoke detector for early detection of fire.
- Self monitoring for contamination, to maintain optimum sensitivity throughout whole life.
- Compatible with diode base to monitor detector removal.
-
Gent Obscuration Test Card Kit For Beam Detector
- Manufacturer: Gent by Honeywell
- Obscuration Test Card Kit
- For Use With Beam Detectors
-
Gent S4-34760 Duct Smoke Sensor Housing with Sensor Base & 0.6m Tube
- Direction of flow indicated by housing.
- Single sampling tube.
- Compatible with S-Quad Sensors.
- Sampling tubes available in three lengths.
- Mounting bracket available.
- Remote LED can be installed via S-Quad monitor output.
- Air Duct uses Venturi process.
- Fully integrated into Vigilon loop.
-
GST DB-01D Common Conventional Detector Diode Base
- Common for all GST DC series detectors.
- Supports detectors locking to prevent unauthorised removal.
- Easy to install with standard mounting options.
-
GST DC-9101E Conventional Combination Smoke & Heat Detector
- Combined optical smoke and A2R class heat detector.
- Supports drift compensation to enable good environmental adaptability.
- Self-diagnostic.
- Local test activation with reed switch.
- Chamber contamination checking.
- All round LED visibility (360° viewing angle) avoids time spent on specific detector orientation.
-
GST DC-9102E Conventional Photoelectric Smoke Detector
- Supports drift compensation to enable good environmental adaptability.
- Self-diagnostic.
- Local test activation with reed switch.
- Chamber contamination checking.
- All round LED visibility (360° viewing angle) avoids time spent on specific detector orientation.
-
GST DC-9103E Conventional Rate-of-Rise & Fixed Temperature Heat Detector
- Self-diagnostic.
- Local test activation with reed switch.
- All round LED visibility (360° viewing angle) avoids time spent on specific detector orientation.
- Configurable polling LED support.
- Remote indicator output.
- 3 Programmable operating levels (A1R, A2S and BS).
-
GST I-9105R Reflective Infrared Beam Smoke Detector
- Wide operating voltage range.
- Large protection areas.
- Combination of transmitter & receiver in one housing allows easy optical alignment.
- Intelligent microprocessor based decision making on fire and fault statuses.
- Easy one person installation & operation due to simple calibration and setup processes.
-
Hochiki CDX Conventional Mounting Base
- Integral remote indicator output
- Low profile, only 8 mm
- Rugged design and electronics free
-
Hochiki Conventional Schottky Diode Base in Ivory or White
- Integral remote indicator output
- In-line Schottky Diode for line continuity
- Low profile, only 8mm
-
Hochiki CDX Conventional Photoelectric Smoke Detector
- Removeable High Performance Chamber
- Remote Indicator Output
- Low Profile Design
- Available in White
-
Hochiki Conventional 2 Wire Base In Ivory or White
- Sav-Wire detector mounting base
- Available in Ivory or White
-
Hochiki DIN Mounting Box Small or Large
- Designed to house up to 6 Hochiki DIN Modules
- Quick-release screws
- Polyurethane gasket provides IP66 protection
- Corrosion free, resistant to most alkaline and acid
- Temperature resistance to +70 deg C, Impact resistant, and Non-flammable
- 32 knock-outs
- Supplied with DIN Rail and fixings
- IP66
-
Hochiki ESP Short Circuit Isolator Base in Ivory or White
- Features integral SCI
- Compatable with Hochiki ESP sensors
- Available in Ivory or White
-
Hochiki FIRElink-100 2 Pipe Aspirating Smoke Detector with Docking Station
- Ultra small, low cost aspirating smoke detector for easy and discreet installation.
- High sensitivity provided by laser based forward light scatter for reliable early warning.
- Two sampling pipes up to 100 m (aggregate) in length (still air).
-
Hochiki FIRElink-25 1 Pipe Aspirating Smoke Detector with Docking Station
- Ultra small, low cost aspirating smoke detector for easy and discreet installation.
- High sensitivity provided by laser based forward light scatter for reliable early warning.
- Single sampling pipe up to 50 m in length (still air).
-
Hochiki FIRElink-400 4 Pipe Aspirating Smoke Detector
- Volt-free Fire-1 and Fault relay outputs are provided for remote monitoring by local fire detection or BMS systems.
- High sensitivity provided by laser based forward light scatter for reliable early warning.
- Four sampling pipes up to 200m (aggregate) in length (still air).
-
Hochiki SDP-3 Duct Detector Mounting Box Including 600mm Pipe
- Allows air duct sampling using standard detector or sensor.
- Fits either square or round section ducting (with additional bracket).
- One-tube air sampling system.
- Simple installation/ maintenance with installer-friendly connection of cables.
- Supplied with standard 600mm sampling pipe.
-
Hochiki SMB Adaptor Plate
- Provides multiple fixing options for the CHQ module range
- Easy to install within the SMB-1 enclosure
- Pre-drilled with correct fixing holes
-
Hochiki Intrinsically Safe Conventional Smoke Detector
- Removable high performance chamber
- Automatic sensitivity window verification with drift compensation
- ATEX classification for intrinsic safety